Description

Fitment： Front Upper Control Arm Ball Joint Sway Bar Suspension Kit For Cadillac Escalade Fitment ： 2002-2006 Cadillac Escalade 2003-2006 Cadillac Escalade ESV 2002-2006 Cadillac Escalade EXT 2002-2006 Chevrolet Avalanche 1500 1999-2006 Chevrolet Silverado 1500 2007 Chevrolet Silverado 1500 Classic 2000-2006 Chevrolet Suburban 1500 2000-2006 Chevrolet Tahoe 2003-2005 GMC Savana 1500 1999-2006 GMC Sierra 1500 2007 GMC Sierra 1500 Classic 2001-2006 GMC Yukon 2001-2006 GMC Yukon XL 1500 Why replace ball joints? Ball joints deteriorate if dirt, grit and impurities get inside or grease escapes, leading to a lack of lubrication. Added to this, rusting and general wear and tear also damage these suspension parts. The effects of this deterioration are excessive play and looseness (beyond the manufacturer’s specifications). While healthy ball joints allow for smooth movement from side to side, they shouldn’t wiggle or jolt up and down. This is a clear indicator that you need to look into ball joint replacement. Watch out for these symptoms of worn ball joints: clunky, knocking noises, particularly when going over bumps creaky or squeaky noises when the suspension moves drifting to the side shaky or loose-feeling steering uneven or premature tyre wear or feathering Here are the steps to replace the ball joints on your suspension: Park the car on stable ground in a garage or parking lot Use a car jack to lift the car, and chock the rear wheels so that the car will not roll away. Take off the wheel and place it securely away from the car Undo the brake callipers, brake rotors and all the hydraulics attached to it Take off sway bars that may be attached to the wheel hub Separate the upper control arm and lower control arm from the suspension using a ball joint fork. Detach the steering knuckle and coil spring You may require a mallet to force the steering knuckle away from the ball joint The ball joint needs to be removed from its housing. Take away any snap rings that are holding the ball joint in place The ball joint press should be used to remove the ball joint from the control arm Inspect the ball joint for any signs of damage or defects. A service manual will describe the state of a worn-out ball joint The new ball joint should be pressed into the control arm using the ball joint press Notes： Please check the fitment chart above before payment making sure all the suspension parts listed on this page are compatible with your automobile. Please refer to Moog official website before narrowing down your search so as to avoid unnecessary item not as described return requests. Package Includes： 2x Front Upper Control Arm And Ball Joint - With Offset Bushings -K80826 2x Front Lower Ball Joint -K6541 2x Front Sway Bar End Link -K8987 1x Front Steering Idler Arm - Heavy Duty -K6534 1x Pitman Arm - With 4 Grooves - Heavy Duty -K6536 Item Specifics Brand Qualitiparts Manufacturer Part Number 11069047 Placement on Vehicle Lower Type Control Arm & Ball Joint Assembly Items Included Mounting Hardware Features Greasable OE/OEM Part Number control arm car,suspension arm,upper control arm ball joint Material Alloy Steel Manufacturer Warranty 1 Year Mounting Style Bolt-On Control Arm Construction Forged Performance Part No Universal Fitment No Vintage Car Part No Cotter Pin Hole Yes Interchange Part Number K80826,K6541,K8987,K6534,K6536,anti sway bar linkage car Superseded Part Number pressing lower ball joint replacement car,stabilizer bar linkage Custom Bundle No Adjustable Yes Finish Coated About Us: We are committed to making the best autoparts products and providing you with better services. So if you have any quesiton or problem, please fell free to contact us about that. Payment: Paypal and any other payments that will be accpeted by eBay are all available. Shipping: 2-8 working days in transit. Product will be shipped within 2 business days after full payment is received and verified. USPS, UPS, FedEx shipping will be provided. Delivery time is about 2-8 business days to most of addresses. Returns: WARNING: Cancer and Reproductive Harm - www.P65Warnings.ca.gov. 30-day free return provided. Contact Us: Any quesiton or problem, do contact us please. We are always online to answer. Note: Do check the compatible chart before paying the items, or contact us for checking the compatibilities for your vehicles/cars/trucks. About Us: Payment: Shipping: Returns: Contact Us: Shop Category Store Home Wheel Spacers Wheel Hub Bearings Lift Kits Additional ABS Parts Control Arms Ball Joints Shocks, Struts & Assemblies Hot Item Front or Rear Wheel Hub & Bearing Assembly For Chevrolet Impala Cadillac XTS CTS USD 67.63 2pcs Front Wheel Hub Bearing Assembly For Nissan Altima S Sedan 4-Door USD 63.89 2pcs Rear Wheel Hub Bearing Assembly For Toyota Yaris Core Hatchback 4-Door 1.5L USD 64.37 2pc Rear Wheel Hub Bearing Assembly For Toyota Corolla Matrix Pontiac Vibe 09-10 USD 63.74 8x Front Upper Control Arms Ball Joints Tie Rods Kit For Ford Ranger Mazda B3000 USD 77.34 Picture New List Item Front Upper Control Arms Ball Joints Sway Bar For Ford F-150 Expedition Lincoln USD 81.99 2pcs Front Complete Shock Strut Coil Spring & Mount For BMW 530i 525i 2004-2006 USD 151.99 Steering Idler Pitman Arm Inner Outer Tie Rod End For Chevrolet C2500 Suburban USD 65.99 2pcs Rear LH+RH Shock Struts Cartridge For Mercedes-Benz Sprinter 2500 2010-2017 USD 48.99 Front Ball Joints Tie Rods Kit For Dodge Ram 2500 Limited Standard Cab Pickup USD 131.99 Help & Info Payment Policy Shipping Policy Return Policy FAQ About Us Front Upper Control Arm Ball Joint Sway Bar Suspension Kit For Cadillac Escalade Fitment ： 2002-2006 Cadillac Escalade 2003-2006 Cadillac Escalade ESV 2002-2006 Cadillac Escalade EXT 2002-2006 Chevrolet Avalanche 1500 1999-2006 Chevrolet Silverado 1500 2007 Chevrolet Silverado 1500 Classic 2000-2006 Chevrolet Suburban 1500 2000-2006 Chevrolet Tahoe 2003-2005 GMC Savana 1500 1999-2006 GMC Sierra 1500 2007 GMC Sierra 1500 Classic 2001-2006 GMC Yukon 2001-2006 GMC Yukon XL 1500 Why replace ball joints? Ball joints deteriorate if dirt, grit and impurities get inside or grease escapes, leading to a lack of lubrication. Added to this, rusting and general wear and tear also damage these suspension parts. The effects of this deterioration are excessive play and looseness (beyond the manufacturer’s specifications). While healthy ball joints allow for smooth movement from side to side, they shouldn’t wiggle or jolt up and down. This is a clear indicator that you need to look into ball joint replacement. Watch out for these symptoms of worn ball joints: clunky, knocking noises, particularly when going over bumps creaky or squeaky noises when the suspension moves drifting to the side shaky or loose-feeling steering uneven or premature tyre wear or feathering Here are the steps to replace the ball joints on your suspension: Park the car on stable ground in a garage or parking lot Use a car jack to lift the car, and chock the rear wheels so that the car will not roll away. Take off the wheel and place it securely away from the car Undo the brake callipers, brake rotors and all the hydraulics attached to it Take off sway bars that may be attached to the wheel hub Separate the upper control arm and lower control arm from the suspension using a ball joint fork. Detach the steering knuckle and coil spring You may require a mallet to force the steering knuckle away from the ball joint The ball joint needs to be removed from its housing. Take away any snap rings that are holding the ball joint in place The ball joint press should be used to remove the ball joint from the control arm Inspect the ball joint for any signs of damage or defects. A service manual will describe the state of a worn-out ball joint The new ball joint should be pressed into the control arm using the ball joint press Notes： Please check the fitment chart above before payment making sure all the suspension parts listed on this page are compatible with your automobile. Please refer to Moog official website before narrowing down your search so as to avoid unnecessary item not as described return requests. Package Includes： 2x Front Upper Control Arm And Ball Joint - With Offset Bushings -K80826 2x Front Lower Ball Joint -K6541 2x Front Sway Bar End Link -K8987 1x Front Steering Idler Arm - Heavy Duty -K6534 1x Pitman Arm - With 4 Grooves - Heavy Duty -K6536 Item Specifics Brand : Qualitiparts Manufacturer Part Number : 11069047 Placement on Vehicle : Lower Type : Control Arm & Ball Joint Assembly Items Included : Mounting Hardware Features : Greasable OE/OEM Part Number : control arm car,suspension arm,upper control arm ball joint Material : Alloy Steel Manufacturer Warranty : 1 Year Mounting Style : Bolt-On Control Arm Construction : Forged Performance Part : No Universal Fitment : No Vintage Car Part : No Cotter Pin Hole : Yes Interchange Part Number : K80826,K6541,K8987,K6534,K6536,anti sway bar linkage car Superseded Part Number : pressing lower ball joint replacement car,stabilizer bar linkage Custom Bundle : No Adjustable : Yes Finish : Coated About Us: We are committed to making the best autoparts products and providing you with better services. So if you have any quesiton or problem, please fell free to contact us about that. Payment: Paypal and any other payments that will be accpeted by eBay are all available. Shipping: 2-8 working days in transit. Product will be shipped within 2 business days after full payment is received and verified. USPS, UPS, FedEx shipping will be provided. Delivery time is about 2-8 business days to most of addresses. Returns: WARNING: Cancer and Reproductive Harm - www.P65Warnings.ca.gov. 30-day free return provided. Contact Us: Any quesiton or problem, do contact us please. We are always online to answer. Note: Do check the compatible chart before paying the items, or contact us for checking the compatibilities for your vehicles/cars/trucks. All rights reserved.